Choke tubes installed

All work is performed with precision tooling on a lathe. Return to top of page. Choke Tube Charts listings are below manufacturers logos. We stock replacement choke tubes for the following gun makers. Invector and Invector Plus. Short and Mag. Short and S. For other manufacturers, not listed above, please call. We can probably find what you are looking for. Choke tubes are offered in three styles. All tubes are manufactured from ph heat-treated stainless steel and available in the following constrictions.

Skeet 1. Improved Cylinder. Skeet 2 Lt. Improved Modified. Extra Full. Turkey Custom Choke Work. This usually entails the opening of the choke. For instance you have a full choke and would like it opened to say improved cylinder.

First before any work is performed, I shoot a check pattern with your gun. While the work proceeds, the gun is test patterned until the proper choke is attained. Turnaround time is 1 to 2 weeks. Perazzi Rib Repair. Loose side ribs for the first inches ahead of the breech is a common problem with all Perazzi's.

We machine the barrel and mechanically fasten the side ribs together. Many of the barrels we repair see 50, rounds a year. After repair, no failures have been reported. Over the years, we have also repaired many Beretta ASE 90 side ribs. Barrel porting. This is a very popular modification usually seen on clay target guns where anything you can do to lessen recoil and fatigue can help put you in the winner's circle. Porting eliminates barrel jump which gives you a quicker second shot when needed.

Porting is becoming extremly popular with dove hunters who normally shoot a lot of shells in a short time frame. It is also popular with waterfowler's who shoot heavy recoiling loads. I use a pattern very similar to Browning's. All barrels are set-up individually, no clamp on drill fixtures or drill motors. All porting is done on a Bridgeport machining center. Turnaround time 1 to 3 days. Lengthening and polishing forcing cones. Lengthening and polishing forcing cones: All shotguns have an area referred to as the forcing cone.

It starts at the end of the chamber and tapers to the bore diameter. Years ago, before plastic wads and modern powders came upon the seen this acted as a gas seal for the over powder cards. What happens when you shoot, as crimp opens the shot charge is pushed through the forcing cone and into the bore. The outside of the shot charge is deformed from the intense pressure and abrupt angle of the forcing cone. Approximately 10 to 15 percent of the pellets are deformed, which causes them to fly out of the pattern.

Deformation of the shot charge is dramatically reduced and pattern density in increased by 8 to 12 percent. It is extremely important to polish the forcing after it has been cut by the reamer, I have seen quite few lengthened cones that were not polished. They tend to build up with plastic from the wads, and also rust rather easily. I recommend leaving them alone, as that is of sufficient length.

Also beware of the extra long forcing cone, back in the 50's and 60's when Ralph Walker developed and tested these reamers he made them as long as 12".

There was no change in performance after 2", so don't get taken in by that garbage. Barrel Dent Repair. We remove dents in 12 and gauge barrels, using a hydraulic dent raiser. GraCoil Installations.

The GraCoil is a compression butt plate with an adjustable tension setting and adjustable pad plate, made to fit any shooter's style. Tension will adjust from 14 lb. The pad plate adjust up or down and side to side with plenty of adjustment for comfort.

Moving parts slide on Teflon liners for a smooth and trouble free motion. Very little lubrication or maintenance is required. The GraCoil adds 1" to the stock length, and requires the stock to be shortened in most cases.

All aluminum and stainless steel construction. Model GC Model GC15 LP Recoil pad not included. Gunfitting and recoil pads installed. Gunfitting and recoil pad installation: I stock Pachmayr and Kick-Eez recoil pads. The price covers, pad installation, cutting stock to proper length and pitch, and contouring pad to stock. All stocks are taped and cut slightly long and ground square and to correct length. The open end grain of the buttstock is sealed with Watco oil.

Adjustable comb installation. We install four-way adjustable comb hardware. This allows the shooter to custom fit the gun to their self. The comb hardware easily adjusts up or down, left or right for the proper cast. The hardware is available in stainless steel or brass.

Please allow 7 to 10 days for installation. Sight installations: I stock many popular brands of shotgun sights including Bradley, Raybar, Lyman and Glow-worm. Usually I can install sights while you wait. All sights and mid beads are guaranteed not to fall out, as they are Loctited in place. Drilling and tapping for scope mount installation for all, Springfields, U. Enfields,Japs, Mausers, Winchester,Remington 30's and all similar bolt action rifles.

Call for quote. Stock repair and refinishing. I only refurnish with oils, to ensure that future stock repairs dealing with any nicks or scratches will garner the best possible results and ensuring that nicks and scratches are completed easily and in a timely manner.

Refinishing with oils enhances the natural beauty of the wood grain. The process in refinishing a stock is as follows:. The existing finish is completely stripped off,.

NOTE: We take great care to prevent damage to the checkering and to maintain the sharp detail of the stocks contour. The oil finish is then applied by hand, buffed, rubbed and re-applied the following day.

This process takes 6 to 12 applications, depending on the type of wood and the woods density. The masking is removed from the checkering. The checkering is chased, cleaned and oiled. The stock is hand oiled and the gun is reassembled. Turnaround time is 4 to 5 weeks. Muzzle brakes installed. I install muzzle brakes on bolt-action rifles and large caliber single-shot pistols.

The installation of a muzzle brake can add between 1" and 1. Upon your request, I will cut the barrel to any length you desire at no extra charge. All work is performed on a state-of-the-art lathe. Blue or Stainless Steel. Remington , Mossberg M Winchester , Please call or e-mail us at the numbers provided below:. Map and Directions Courtesy Of.

We currently accept payment through the following methods. Processing Source a division of Accesspoint Corporation. Contact zazu processingsource. Shipping is the sole responsibility of the sender. The information listed below is current as of January 1, , and is provided as a guidline for your shipping needs. Please contact the USPS or your carrier of choice for the most up to date information.

Realize that packing for shipping is different from packing for moving. Package and freight carriers are far rougher on boxes than are movers. Place the weapon back in its original box. If you no longer have the original box, wrap the object in a similarly sized box with enough packaging so that you don't hear anything move when you shake the box.

Pack the first box into a slightly larger box. Insert at least two inches of padding between the inner box and the sides of the outer box. Include a short letter with. Phone Number, with area code. A detailed description of the problem or work to be performed. Your preferred method for return shipment. Ship the box. Registered Mail. Provides maximum protection and security for valuables. May be combined with COD, restricted delivery, or return receipt.

Only items with no declared value may use registry service without insurance. Priority Mail. Priority Mail offers 2-day service to most domestic destinations. Items must weigh 70 pounds or less and measure inches or less in. Priority Mail envelopes, labels, and boxes are available at no additional charge at post offices or by calling You may also send your shotgun via the following carriers:.

The Internet's leading shotgun resource since Shooting Organizations. Places to Shoot. Courtesy Of. Alex Imports Frontage Rd. Visit our Web Site at: sites. American Arms, Inc. Also Uberti lever action rifles, single action revolvers. Vist our Web Site at: sites. Armsport, Inc. Arrieta Manufacturas, S. Also double rifles and bolt rifles, in all calibers. Sporting clothing and accessories.

Breech loading rifles available in requested calibres. Benelli USA Corp. Beretta U. Pistols, knives, gun cases, Beretta Sport clothing and accessories. Visit our Web Site at: www. Gun and Rifle Makers 13 Dover St.

Robertson Est: E-mail: bossguns aol. Over and Under; available in 12, 20, 28 gauge and. Over and Under rifles available in heavy calibres. British Sporting Arms Ltd. Call for our new catalogue or visit us at our retail store. Brolin Industries, Inc.

Complete line sporting firearms, gun accessories, gun safes, gun cases, knives, footwear, clothing and archery equipment for the outdoor enthusiast. Century International Arms, Inc. PO Box , 5 Lemnah Dr. Chapuis Armes Z. La Gravoux, B. Manufactured on a limited basis. Churchill Gunmakers Ltd. Ockley Rd. Benelli Crio. Tru -Choke SD. Benelli Crio Plus.

Franchi old style. Hatsan Escort V1. Trulock offers several other choke tube designs not listed. We want you to be satisfied with our products and will do anything within reason to make you happy. Anybody can take your money and ship you merchandise. Our Warranty and Satisfaction Guarantee All chokes are warrantied against failure for life. If you are not satisfied in any way with our product you can return it for exchange or a refund of the purchase price less shipping charges within 60 days from the invoice date.

A copy of the invoice must be returned with the choke in question. Our choke tubes are heat treated to a high strength level to resist wear and choke creep. Our choke tubes are marked on the head and body with the name of the specific constriction. The exact exit diameter in thousandths of an inch is engraved on the body.

Trulock offers as stock items the largest range of choke designs to fit shotguns of almost all brands. Our choke tubes are precision made with tight tolerances on state of the art CNC equipment.

We produce the choke tubes in our factory in Whigham Ga. Powered by X-Cart. Sign in Register. Guaranteed Since Looking for the right choke?

CALL: Sign up for our Email Newsletter. Trulock offers shotgun choke tubes for any shooting ac tivity. We make over 2, different shotgun chokes. All rights reserved. Skeet Shooting. Waterfowl Hunting. Home Defense. Trap Shooting. Upland Bird Hunting. Law Enforcement. Sporting Clays. Small Game Hunting. Card Shooting. Turkey Hunting. Predator Hunting.